? semiconductor components industries, llc, 2006 september, 2006 ? rev. 2 1 publication order number: MSRP10040/d MSRP10040 switchmode ? soft recovery power rectifier powertap ? iii package state of the art geometry features epitaxial construction with glass passivation and metal overlay contact. ideally suited for low voltage, high frequency switching power supplies, free wheeling diode and polarity protection diodes. ? soft recovery rectifier ? low i rrm losses ? highly stable glass passivated junction mechanical characteristics: ? dual die construction ? case: epoxy, molded with plated copper heatsink base ? weight: 40 grams (approximately) ? finish: all external surfaces corrosion resistant ? top terminal torque: 25 ? 40 lb ? in max. ? shipped 50 units per foam ? marking: MSRP10040 maximum ratings rating symbol max unit peak repetitive reverse voltage working peak reverse voltage dc blocking voltage v rrm v rwm v r 400 v average rectified forward current (at rated v r , t c = 100 c) i o 100 a peak repetitive forward current (at rated v r , square wave, 100 khz, t c = tbd c) i frm 200 a non ? repetitive peak surge current (surge applied at rated load conditions halfwave, single phase, 60 hz) i fsm 800 a storage/operating case temperature range t stg , t c ? 55 to +150 c operating junction temperature range t j ? 55 to +150 c soft recovery rectifier 100 amperes 400 volts device package shipping ordering information MSRP10040 powertap iii 50 units/tray powertap iii case 357d plastic http://onsemi.com 1 2 1 2 marking diagram MSRP10040 MSRP10040 = device code
MSRP10040 http://onsemi.com 2 thermal characteristics rating symbol value unit thermal resistance ? junction ? to ? case r jc 0.5 c/w electrical characteristics typical instantaneous forward voltage (note 1.) v f t j = 25 c t j = 100 c volts (i f = 100 a) (i f = 200 a) 1.75 2.00 1.25 1.50 typical instantaneous reverse current i r t j = 25 c t j = 100 c a (v r = 400 v) (v r = 200 v) 100 50 500 250 typical reverse recovery time (note 2.) (v r = 30 v, i f = 10 a, di/dt = 200 a/ s) t rr 75 ns typical peak reverse recovery current (v r = 30 v, i f = 10 a, di/dt = 200 a/ s) i rm 7.0 amps 1. pulse test: pulse width 250 s, duty cycle 2%. 2. t rr measured projecting from 25% of irm to zero.
MSRP10040 http://onsemi.com 3 package dimensions powertap iii case 357d ? 01 issue a dim min max min max millimeters inches a 1.520 1.560 38.61 39.62 b 0.783 0.813 19.89 20.65 c 0.615 0.635 15.62 16.13 d 0.152 0.162 3.86 4.11 e 0.120 0.130 3.05 3.30 f 0.435 0.445 11.05 11.30 h 0.007 0.030 0.18 0.76 l 0.210 0.230 5.33 5.84 n 1/4?20unc?2b 1/4?20unc?2b q 0.152 0.162 3.86 4.11 r 1.175 1.195 29.85 30.35 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. terminal penetration: 5.97 (0.235) maximum. r d b n a q l 2 pl c f h e radius on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5773 ? 3850 MSRP10040/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative powertap and switchmode are trademarks of semiconductor components industries, llc.
|
